538 lines
14 KiB
Plaintext
538 lines
14 KiB
Plaintext
|
;
|
||
|
; chan_misdn sample config
|
||
|
;
|
||
|
|
||
|
; general section:
|
||
|
;
|
||
|
; for debugging and general setup, things that are not bound to port groups
|
||
|
;
|
||
|
|
||
|
[general]
|
||
|
;
|
||
|
; Sets the Path to the misdn-init.conf (for nt_ptp mode checking)
|
||
|
;
|
||
|
misdn_init=/etc/misdn-init.conf
|
||
|
|
||
|
; set debugging flag:
|
||
|
; 0 - No Debug
|
||
|
; 1 - mISDN Messages and * - Messages, and * - State changes
|
||
|
; 2 - Messages + Message specific Informations (e.g. bearer capability)
|
||
|
; 3 - very Verbose, the above + lots of Driver specific infos
|
||
|
; 4 - even more Verbose than 3
|
||
|
;
|
||
|
; default value: 0
|
||
|
;
|
||
|
debug=0
|
||
|
|
||
|
|
||
|
|
||
|
; set debugging file and flags for mISDNuser (NT-Stack)
|
||
|
;
|
||
|
; flags can be or'ed with the following values:
|
||
|
;
|
||
|
; DBGM_NET 0x00000001
|
||
|
; DBGM_MSG 0x00000002
|
||
|
; DBGM_FSM 0x00000004
|
||
|
; DBGM_TEI 0x00000010
|
||
|
; DBGM_L2 0x00000020
|
||
|
; DBGM_L3 0x00000040
|
||
|
; DBGM_L3DATA 0x00000080
|
||
|
; DBGM_BC 0x00000100
|
||
|
; DBGM_TONE 0x00000200
|
||
|
; DBGM_BCDATA 0x00000400
|
||
|
; DBGM_MAN 0x00001000
|
||
|
; DBGM_APPL 0x00002000
|
||
|
; DBGM_ISDN 0x00004000
|
||
|
; DBGM_SOCK 0x00010000
|
||
|
; DBGM_CONN 0x00020000
|
||
|
; DBGM_CDATA 0x00040000
|
||
|
; DBGM_DDATA 0x00080000
|
||
|
; DBGM_SOUND 0x00100000
|
||
|
; DBGM_SDATA 0x00200000
|
||
|
; DBGM_TOPLEVEL 0x40000000
|
||
|
; DBGM_ALL 0xffffffff
|
||
|
;
|
||
|
|
||
|
ntdebugflags=0
|
||
|
ntdebugfile=/var/log/misdn-nt.log
|
||
|
|
||
|
|
||
|
; some pbx systems do cut the L1 for some milliseconds, to avoid
|
||
|
; dropping running calls, we can set this flag to yes and tell
|
||
|
; mISDNuser not to drop the calls on L2_RELEASE
|
||
|
ntkeepcalls=no
|
||
|
|
||
|
; the big trace
|
||
|
;
|
||
|
; default value: [not set]
|
||
|
;
|
||
|
;tracefile=/var/log/asterisk/misdn.log
|
||
|
|
||
|
|
||
|
; set to yes if you want mISDN_dsp to bridge the calls in HW
|
||
|
;
|
||
|
; default value: yes
|
||
|
;
|
||
|
bridging=no
|
||
|
|
||
|
|
||
|
; stops dialtone after getting first digit on nt Port
|
||
|
;
|
||
|
; default value: yes
|
||
|
;
|
||
|
stop_tone_after_first_digit=yes
|
||
|
|
||
|
; whether to append overlapdialed Digits to Extension or not
|
||
|
;
|
||
|
; default value: yes
|
||
|
;
|
||
|
append_digits2exten=yes
|
||
|
|
||
|
;;; CRYPTION STUFF
|
||
|
|
||
|
; Whether to look for dynamic crypting attempt
|
||
|
;
|
||
|
; default value: no
|
||
|
;
|
||
|
dynamic_crypt=no
|
||
|
|
||
|
; crypt_prefix, what is used for crypting Protocol
|
||
|
;
|
||
|
; default value: [not set]
|
||
|
;
|
||
|
crypt_prefix=**
|
||
|
|
||
|
; Keys for cryption, you reference them in the dialplan
|
||
|
; later also in dynamic encr.
|
||
|
;
|
||
|
; default value: [not set]
|
||
|
;
|
||
|
crypt_keys=test,muh
|
||
|
|
||
|
; ----------------------------- JITTER BUFFER CONFIGURATION --------------------------
|
||
|
; jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of a
|
||
|
; SIP channel. Defaults to "no". An enabled jitterbuffer will
|
||
|
; be used only if the sending side can create and the receiving
|
||
|
; side can not accept jitter. The SIP channel can accept jitter,
|
||
|
; thus a jitterbuffer on the receive SIP side will be used only
|
||
|
; if it is forced and enabled.
|
||
|
|
||
|
; jbforce = no ; Forces the use of a jitterbuffer on the receive side of a SIP
|
||
|
; channel. Defaults to "no".
|
||
|
|
||
|
; jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds.
|
||
|
|
||
|
; jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is
|
||
|
; resynchronized. Useful to improve the quality of the voice, with
|
||
|
; big jumps in/broken timestamps, usually sent from exotic devices
|
||
|
; and programs. Defaults to 1000.
|
||
|
|
||
|
; jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of a SIP
|
||
|
; channel. Two implementations are currently available - "fixed"
|
||
|
; (with size always equals to jbmaxsize) and "adaptive" (with
|
||
|
; variable size, actually the new jb of IAX2). Defaults to fixed.
|
||
|
|
||
|
; jbtargetextra = 40 ; This option only affects the jb when 'jbimpl = adaptive' is set.
|
||
|
; The option represents the number of milliseconds by which the new
|
||
|
; jitter buffer will pad its size. the default is 40, so without
|
||
|
; modification, the new jitter buffer will set its size to the jitter
|
||
|
; value plus 40 milliseconds. increasing this value may help if your
|
||
|
; network normally has low jitter, but occasionally has spikes.
|
||
|
|
||
|
; jblog = no ; Enables jitterbuffer frame logging. Defaults to "no".
|
||
|
; ----------------------------------------------------------------------------------
|
||
|
|
||
|
; users sections:
|
||
|
;
|
||
|
; name your sections as you wish but not "general" or "default" !
|
||
|
; the sections are Groups, you can dial out in extensions.conf
|
||
|
; with Dial(mISDN/g:extern/101) where extern is a section name,
|
||
|
; chan_misdn tries every port in this section to find a
|
||
|
; new free channel
|
||
|
;
|
||
|
; The default section is not a group section, it just contains config elements
|
||
|
; which are inherited by group sections.
|
||
|
;
|
||
|
[default]
|
||
|
|
||
|
; define your default context here
|
||
|
;
|
||
|
; default value: default
|
||
|
;
|
||
|
context=misdn
|
||
|
|
||
|
; language
|
||
|
;
|
||
|
; default value: en
|
||
|
;
|
||
|
language=en
|
||
|
|
||
|
;
|
||
|
; This option specifies a default music on hold class to
|
||
|
; use when put on hold if the channel's moh class was not
|
||
|
; explicitly set with Set(CHANNEL(musicclass)=whatever) and
|
||
|
; the peer channel did not suggest a class to use.
|
||
|
;
|
||
|
musicclass=default
|
||
|
|
||
|
;
|
||
|
; Either if we should produce DTMF Tones ourselves
|
||
|
;
|
||
|
senddtmf=yes
|
||
|
|
||
|
;
|
||
|
; If we should generate Ringing for chan_sip and others
|
||
|
;
|
||
|
far_alerting=no
|
||
|
|
||
|
|
||
|
;
|
||
|
; Here you can list which bearer capabilities should be allowed:
|
||
|
; all - allow any bearer capability
|
||
|
; speech - allow speech
|
||
|
; 3_1khz - allow 3.1KHz audio
|
||
|
; digital_unrestricted - allow unrestricted digital
|
||
|
; digital_restricted - allow restricted digital
|
||
|
; video - allow video
|
||
|
;
|
||
|
; Example:
|
||
|
; allowed_bearers=speech,3_1khz
|
||
|
;
|
||
|
allowed_bearers=all
|
||
|
|
||
|
; Incoming number prefixes for the indicated Type-Of-Number. These are
|
||
|
; inserted before any number (caller, dialed, connected, redirecting,
|
||
|
; redirection) received from the ISDN link if that number has the
|
||
|
; corresponding Type-Of-Number.
|
||
|
; See the dialplan options.
|
||
|
;
|
||
|
; default values:
|
||
|
; unknownprefix=
|
||
|
; internationalprefix=00
|
||
|
; nationalprefix=0
|
||
|
; netspecificprefix=
|
||
|
; subscriberprefix=
|
||
|
; abbreviatedprefix=
|
||
|
;
|
||
|
;unknownprefix=
|
||
|
internationalprefix=00
|
||
|
nationalprefix=0
|
||
|
;netspecificprefix=
|
||
|
;subscriberprefix=
|
||
|
;abbreviatedprefix=
|
||
|
|
||
|
; set rx/tx gains between -8 and 8 to change the RX/TX Gain
|
||
|
;
|
||
|
; default values: rxgain: 0
|
||
|
; txgain: 0
|
||
|
;
|
||
|
rxgain=0
|
||
|
txgain=0
|
||
|
|
||
|
; some telcos especially in NL seem to need this set to yes, also in
|
||
|
; switzerland this seems to be important
|
||
|
;
|
||
|
; default value: no
|
||
|
;
|
||
|
te_choose_channel=no
|
||
|
|
||
|
|
||
|
|
||
|
;
|
||
|
; Monitors L1 of the port. If L1 is down it tries
|
||
|
; to bring it up. The polling timeout is given in seconds.
|
||
|
; Setting the value to 0 disables monitoring L1 of the port.
|
||
|
;
|
||
|
; default value: 0
|
||
|
;
|
||
|
; This option is only read at chan_misdn loading time.
|
||
|
; You need to unload and load chan_misdn to change the
|
||
|
; value. An asterisk restart will also do the trick.
|
||
|
;
|
||
|
l1watcher_timeout=0
|
||
|
|
||
|
;
|
||
|
; This option defines, if chan_misdn should check the L1 on a PMP
|
||
|
; before making a group call on it. The L1 may go down for PMP Ports
|
||
|
; so we might need this.
|
||
|
; But be aware! a broken or plugged off cable might be used for a group call
|
||
|
; as well, since chan_misdn has no chance to distinguish if the L1 is down
|
||
|
; because of a lost Link or because the Provider shut it down...
|
||
|
;
|
||
|
; default: no
|
||
|
;
|
||
|
pmp_l1_check=no
|
||
|
|
||
|
|
||
|
;
|
||
|
; in PMP this option defines which cause should be sent out to
|
||
|
; the 3. caller. chan_misdn does not support callwaiting on TE
|
||
|
; PMP side. This allows to modify the RELEASE_COMPLETE cause
|
||
|
; at least.
|
||
|
;
|
||
|
reject_cause=16
|
||
|
|
||
|
|
||
|
;
|
||
|
; Send Setup_Acknowledge on incoming calls anyway (instead of PROCEEDING),
|
||
|
; this requests additional Infos, so we can waitfordigits
|
||
|
; without much issues. This works only for PTP Ports
|
||
|
;
|
||
|
; default value: no
|
||
|
;
|
||
|
need_more_infos=no
|
||
|
|
||
|
|
||
|
;
|
||
|
; set this to yes if you want to disconnect calls when a timeout occurs
|
||
|
; for example during the overlapdial phase
|
||
|
;
|
||
|
nttimeout=no
|
||
|
|
||
|
; Set the method to use for channel selection:
|
||
|
; standard - Use the first free channel starting from the lowest number.
|
||
|
; standard_dec - Use the first free channel starting from the highest number.
|
||
|
; round_robin - Use the round robin algorithm to select a channel. Use this
|
||
|
; if you want to balance your load.
|
||
|
;
|
||
|
; default value: standard
|
||
|
;
|
||
|
method=standard
|
||
|
|
||
|
|
||
|
; specify if chan_misdn should collect digits before going into the
|
||
|
; dialplan, you can choose yes=4 Seconds, no, or specify the amount
|
||
|
; of seconds you need;
|
||
|
;
|
||
|
overlapdial=yes
|
||
|
|
||
|
;
|
||
|
; dialplan means Type Of Number in ISDN Terms
|
||
|
; There are different types of the dialplan:
|
||
|
;
|
||
|
; dialplan -> for outgoing call's dialed number
|
||
|
; localdialplan -> for outgoing call's callerid
|
||
|
; (if -1 is set use the value from the asterisk channel)
|
||
|
; cpndialplan -> for incoming call's connected party number sent to caller
|
||
|
; (if -1 is set use the value from the asterisk channel)
|
||
|
;
|
||
|
; dialplan options:
|
||
|
;
|
||
|
; 0 - unknown
|
||
|
; 1 - International
|
||
|
; 2 - National
|
||
|
; 3 - Network-Specific
|
||
|
; 4 - Subscriber
|
||
|
; 5 - Abbreviated
|
||
|
;
|
||
|
; default value: 0
|
||
|
;
|
||
|
dialplan=0
|
||
|
localdialplan=0
|
||
|
cpndialplan=0
|
||
|
|
||
|
|
||
|
|
||
|
;
|
||
|
; turn this to no if you don't mind correct handling of Progress Indicators
|
||
|
;
|
||
|
early_bconnect=yes
|
||
|
|
||
|
|
||
|
;
|
||
|
; turn this on if you like to send Tone Indications to a Incoming
|
||
|
; isdn channel on a TE Port. Rarely used, only if the Telco allows
|
||
|
; you to send indications by yourself, normally the Telco sends the
|
||
|
; indications to the remote party.
|
||
|
;
|
||
|
; default: no
|
||
|
;
|
||
|
incoming_early_audio=no
|
||
|
|
||
|
; uncomment the following to get into s extension at extension conf
|
||
|
; there you can use DigitTimeout if you can't or don't want to use
|
||
|
; isdn overlap dial.
|
||
|
; note: This will jump into the s exten for every exten!
|
||
|
;
|
||
|
; default value: no
|
||
|
;
|
||
|
;always_immediate=no
|
||
|
|
||
|
;
|
||
|
; set this to yes if you want to generate your own dialtone
|
||
|
; with always_immediate=yes, else chan_misdn generates the dialtone
|
||
|
;
|
||
|
; default value: no
|
||
|
;
|
||
|
nodialtone=no
|
||
|
|
||
|
|
||
|
; uncomment the following if you want callers which called exactly the
|
||
|
; base number (so no extension is set) jump to the s extension.
|
||
|
; if the user dials something more it jumps to the correct extension
|
||
|
; instead
|
||
|
;
|
||
|
; default value: no
|
||
|
;
|
||
|
;immediate=no
|
||
|
|
||
|
; uncomment the following to have hold and retrieve support
|
||
|
;
|
||
|
; default value: no
|
||
|
;
|
||
|
;hold_allowed=yes
|
||
|
|
||
|
; Pickup and Callgroup
|
||
|
;
|
||
|
; default values: not set = 0
|
||
|
; range: 0-63
|
||
|
;
|
||
|
;callgroup=1
|
||
|
;pickupgroup=1
|
||
|
|
||
|
; Named pickup groups and named call groups
|
||
|
;
|
||
|
; give a name to groups and configure any number of groups
|
||
|
;
|
||
|
;namedcallgroup=engineering,sales,netgroup,protgroup
|
||
|
;namedpickupgroup=sales
|
||
|
|
||
|
; Set the outgoing caller id to the value.
|
||
|
;callerid="name" <number>
|
||
|
|
||
|
;
|
||
|
; these are the exact isdn screening and presentation indicators
|
||
|
; if -1 is given for either value the presentation indicators are used
|
||
|
; from asterisks CALLERPRES function.
|
||
|
; s=0, p=0 -> callerid presented
|
||
|
; s=1, p=1 -> callerid restricted (the remote end does not see it!)
|
||
|
;
|
||
|
; default values s=-1, p=-1
|
||
|
presentation=-1
|
||
|
screen=-1
|
||
|
|
||
|
; Incoming calls will have a caller ID tag set to this value
|
||
|
;
|
||
|
;incoming_cid_tag = "asterisk"
|
||
|
|
||
|
; With this set, you can automatically append the MSN of a party
|
||
|
; to the cid_tag. Incoming calls have the dialed number appended
|
||
|
; to the tag, and outgoing calls have the caller number appended
|
||
|
; to the tag. An '_' is used to separate the tag from the
|
||
|
; MSN.
|
||
|
; Default is no.
|
||
|
;
|
||
|
;append_msn_to_cid_tag = no
|
||
|
|
||
|
; Select what to do with outgoing COLP information on this port.
|
||
|
;
|
||
|
; 0 - Send out COLP information unaltered. (default)
|
||
|
; 1 - Force COLP to restricted on all outgoing COLP information.
|
||
|
; 2 - Do not send COLP information.
|
||
|
outgoing_colp=0
|
||
|
|
||
|
; Put a display ie in the CONNECT message containing the following
|
||
|
; information if it is available (nt port only):
|
||
|
;
|
||
|
; 0 - Do not put the connected line information in the display ie.
|
||
|
; 1 - Put the available connected line name in the display ie.
|
||
|
; 2 - Put the available connected line number in the display ie.
|
||
|
; 3 - Put the available connected line name and number in the display ie.
|
||
|
;
|
||
|
display_connected=0
|
||
|
|
||
|
; Put a display ie in the SETUP message containing the following
|
||
|
; information if it is available (nt port only):
|
||
|
;
|
||
|
; 0 - Do not put the caller information in the display ie.
|
||
|
; 1 - Put the available caller name in the display ie.
|
||
|
; 2 - Put the available caller number in the display ie.
|
||
|
; 3 - Put the available caller name and number in the display ie.
|
||
|
;
|
||
|
display_setup=0
|
||
|
|
||
|
; This enables echo cancellation with the given number of taps.
|
||
|
; Be aware: Move this setting only to outgoing portgroups!
|
||
|
; A value of zero turns echo cancellation off.
|
||
|
;
|
||
|
; possible values are: 0,32,64,128,256,yes(=128),no(=0)
|
||
|
;
|
||
|
; default value: no
|
||
|
;
|
||
|
;echocancel=no
|
||
|
|
||
|
;
|
||
|
; chan_misdns jitterbuffer, default 4000
|
||
|
;
|
||
|
jitterbuffer=4000
|
||
|
|
||
|
;
|
||
|
; change this threshold to enable dejitter functionality
|
||
|
;
|
||
|
jitterbuffer_upper_threshold=0
|
||
|
|
||
|
|
||
|
;
|
||
|
; change this to yes, if you want to bridge a mISDN data channel to
|
||
|
; another channel type or to an application.
|
||
|
;
|
||
|
hdlc=no
|
||
|
|
||
|
|
||
|
;
|
||
|
; defines the maximum amount of incoming calls per port for
|
||
|
; this group. Calls which exceed the maximum will be marked with
|
||
|
; the channel variable MAX_OVERFLOW. It will contain the amount of
|
||
|
; overflowed calls
|
||
|
;
|
||
|
max_incoming=-1
|
||
|
|
||
|
;
|
||
|
; defines the maximum amount of outgoing calls per port for this group
|
||
|
; exceeding calls will be rejected
|
||
|
;
|
||
|
max_outgoing=-1
|
||
|
|
||
|
;
|
||
|
; Enable/disable the call-completion retention option support (ptp only).
|
||
|
;
|
||
|
; Note: To use the CCBS/CCNR supplementary service feature and other
|
||
|
; supplementary services using FACILITY messages requires a
|
||
|
; modified version of mISDN from:
|
||
|
; http://svn.digium.com/svn/thirdparty/mISDN/trunk
|
||
|
; http://svn.digium.com/svn/thirdparty/mISDNuser/trunk
|
||
|
;
|
||
|
cc_request_retention=yes
|
||
|
|
||
|
[intern]
|
||
|
; define your ports, e.g. 1,2 (depends on mISDN-driver loading order)
|
||
|
ports=1,2
|
||
|
; context where to go to when incoming Call on one of the above ports
|
||
|
context=Intern
|
||
|
|
||
|
[internPP]
|
||
|
;
|
||
|
; adding the postfix 'ptp' to a port number is obsolete now, chan_misdn
|
||
|
; parses /etc/misdn-init.conf and sets the ptp mode to the corresponding
|
||
|
; configs. For backwards compatibility you can still set ptp here.
|
||
|
;
|
||
|
ports=3
|
||
|
|
||
|
[first_extern]
|
||
|
; again port defs
|
||
|
ports=4
|
||
|
; again a context for incoming calls
|
||
|
context=Extern1
|
||
|
; msns for te ports, listen on those numbers on the above ports, and
|
||
|
; indicate the incoming calls to asterisk
|
||
|
; here you can give a comma separated list or simply an '*' for
|
||
|
; any msn.
|
||
|
msns=*
|
||
|
|
||
|
; here an example with given msns
|
||
|
[second_extern]
|
||
|
ports=5
|
||
|
context=Extern2
|
||
|
callerid="Asterisk" <1234>
|
||
|
msns=102,144,101,104
|